Port City Makerspace - User contributions [en]

Studio mod.360 Knitting Machine

2026-09-22T21:55:04Z

AndrewT:

[[File:2026-09-16 19.59.56.jpg|350px|thumb|]]
[[File:2026-09-16 19.59.21.jpg|400px|thumb|Full View]]

=About our machine=
This Studio Mod.360 is a vintage, 4.5mm gauge metal-bed knitting machine. It was also sold under the brand names Singer, Silver Reed, and Knitmaster.

=Guides and Manuals=
*[https://drive.google.com/file/d/1RQePQRn3OykiCoR-nrMPoxv5J0CLy6NS/view?usp=drive_link Manual]
*[https://textilemakerspace.stanford.edu/tutorials/basic-studio-mod-360/ Instructions and Tips]

=Safety=

=Tips=

=Helpful Videos=
*[https://www.youtube.com/watch?v=jOEQHbPcVNE Beginner instruction video (featuring clone model of our machine)]
*[https://www.youtube.com/watch?v=AMSZFb4g184 How To Set Up A Knitting Machine]

=Maintenance=
*See Manual

[[Category: Tool]]
[[Category: Textiles Lab]]

Studio mod.360 Knitting Machine

2026-09-22T21:50:38Z

AndrewT: /* About our machine */

[[File:2026-09-16 19.59.56.jpg|350px|thumb|]]
[[File:2026-09-16 19.59.21.jpg|400px|thumb|Full View]]
[[File:2026-09-16 20.03.06.jpg|400px|thumb|Service Info]]

Studio Mod.360

=About our machine=
This Studio Mod.360 is a vintage, 4.5mm gauge metal-bed knitting machine. It was also sold under the brand names Singer, Silver Reed, and Knitmaster.

=Guides and Manuals=
*[https://drive.google.com/file/d/1RQePQRn3OykiCoR-nrMPoxv5J0CLy6NS/view?usp=drive_link Manual]
*[https://textilemakerspace.stanford.edu/tutorials/basic-studio-mod-360/ Instructions and Tips]

=Safety=

=Tips=

=Helpful Videos=
*[https://www.youtube.com/watch?v=jOEQHbPcVNE Beginner instruction video (featuring clone model of our machine)]
*[https://www.youtube.com/watch?v=AMSZFb4g184 How To Set Up A Knitting Machine]

=Maintenance=
*See Manual

[[Category: Tool]]
[[Category: Textiles Lab]]

LK100 Knitting Machine

2026-09-22T21:49:47Z

AndrewT: AndrewT moved page LK100 Knitting Machine to Studio mod.360 Knitting Machine: Wrong model name

#REDIRECT [[Studio mod.360 Knitting Machine]]

Studio mod.360 Knitting Machine

2026-09-22T21:49:47Z

AndrewT: AndrewT moved page LK100 Knitting Machine to Studio mod.360 Knitting Machine: Wrong model name

Studio mod.360 Knitting Machine

2026-09-22T21:48:22Z

AndrewT:

Studio mod.360 Knitting Machine

2026-09-22T21:22:28Z

AndrewT: Redirected manual link to Google Drive upload

[[File:2026-09-16 19.59.56.jpg|350px|thumb|]]
[[File:2026-09-16 19.59.21.jpg|400px|thumb|Full View]]
[[File:2026-09-16 20.03.06.jpg|400px|thumb|Service Info]]

Studio Mod.360

=About our machine=
Singer/Silver Reed LK100 is a vintage, 9mm gauge bulky plastic-bed knitting machine that is widely considered a great, forgiving workhorse for beginners working with worsted-weight and bulky yarns.

=Guides and Manuals=
*[https://drive.google.com/file/d/1RQePQRn3OykiCoR-nrMPoxv5J0CLy6NS/view?usp=drive_link Manual]
*[https://textilemakerspace.stanford.edu/tutorials/basic-studio-mod-360/ Instructions and Tips (for similar style machine)]

=Safety=
*Knitting is generally a safe, accessible craft, but physical strain and ergonomic issues can occur during long crafting sessions.

=Tips=
*Beginner Friendly: The larger 9mm needles have bigger hooks and are less prone to bending than fine-gauge needles, saving new users a lot of frustration.

=Helpful Videos=
*[https://youtu.be/A1zwp88_Mmw Singer LK 100 Knit Machine Instructions 1/2]
*[https://youtu.be/WwrOpdx-fFg Singer LK 100 Knit Machine Instructions 2/2]

=Maintenance=
*See Manual

[[Category: Tool]]
[[Category: Textiles Lab]]

Studio mod.360 Knitting Machine

2026-09-22T21:13:13Z

AndrewT: Adding photos

[[File:2026-09-16 19.59.56.jpg|400px|thumb|]]
[[File:2026-09-16 19.59.21.jpg|400px|thumb|Full View]]
[[File:2026-09-16 20.03.06.jpg|400px|thumb|Service Info]]

Studio Mod.360

=About our machine=
Singer/Silver Reed LK100 is a vintage, 9mm gauge bulky plastic-bed knitting machine that is widely considered a great, forgiving workhorse for beginners working with worsted-weight and bulky yarns.

=Guides and Manuals=
*[https://mkmanuals.com/singer-lk100-knitting-machine-instruction-manual.html Manual]
*[https://textilemakerspace.stanford.edu/tutorials/basic-studio-mod-360/ Instructions and Tips (for similar style machine)]

=Safety=
*Knitting is generally a safe, accessible craft, but physical strain and ergonomic issues can occur during long crafting sessions.

=Tips=
*Beginner Friendly: The larger 9mm needles have bigger hooks and are less prone to bending than fine-gauge needles, saving new users a lot of frustration.

=Helpful Videos=
*[https://youtu.be/A1zwp88_Mmw Singer LK 100 Knit Machine Instructions 1/2]
*[https://youtu.be/WwrOpdx-fFg Singer LK 100 Knit Machine Instructions 2/2]

=Maintenance=
*See Manual

[[Category: Tool]]
[[Category: Textiles Lab]]

Studio mod.360 Knitting Machine

2026-09-22T21:06:10Z

AndrewT: Editing links to provide descriptions

Singer LK100 Knitting Machine

=About our machine=
Singer/Silver Reed LK100 is a vintage, 9mm gauge bulky plastic-bed knitting machine that is widely considered a great, forgiving workhorse for beginners working with worsted-weight and bulky yarns.

=Guides and Manuals=
*[https://mkmanuals.com/singer-lk100-knitting-machine-instruction-manual.html Manual]
*[https://textilemakerspace.stanford.edu/tutorials/basic-studio-mod-360/ Instructions and Tips (for similar style machine)]

=Safety=
*Knitting is generally a safe, accessible craft, but physical strain and ergonomic issues can occur during long crafting sessions.

=Tips=
*Beginner Friendly: The larger 9mm needles have bigger hooks and are less prone to bending than fine-gauge needles, saving new users a lot of frustration.

=Helpful Videos=
*[https://youtu.be/A1zwp88_Mmw Singer LK 100 Knit Machine Instructions 1/2]
*[https://youtu.be/WwrOpdx-fFg Singer LK 100 Knit Machine Instructions 2/2]

=Maintenance=
*See Manual

[[Category: Tool]]
[[Category: Textiles Lab]]

Walker-Turner Bandsaw

2025-07-29T22:41:27Z

AndrewT: Beginning process

'''PAGE IN PROGRESS'''

Physical details:
*Blade length: "
*Blade width:
*Maximum Cutting Width (throat):
*Maximum Cutting Depth (height):

=Manual and Guides=

=Use and Cleanup=
#Use the right blade for your job. A thicker blade (1/2" or larger) is best for straight cuts in thick material. A thinner blade (around 1/4" or smaller) is better for curved cuts in thin material. If you are needing to resaw or mill larger pieces to size, consider using the more powerful Rockwell.
#Adjust the blade guard to slightly above the material you will be cutting.
#Make sure the saw's blast gate on the dust collection system is open, and all others (that aren't in use) are closed, and turn dust collector on.
#Clean up when you are done. Use a handbroom or vacuum to clean the table, underneath the table, and the lower compartment where dust really collects.
#Lower the blade guard when you are done. This is for safety - less exposed blade means less risk to people in the shop.

=Videos=

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Rockwell Bandsaw

2025-07-29T22:35:37Z

AndrewT: Redirected page to Resaw Bandsaw

#REDIRECT [[Resaw Bandsaw]]

Category:Spaces

2025-07-16T01:26:06Z

AndrewT:

*[[Auto Shop]], use the car lift to do serious auto-repair.
*[[Bike Shop]], for tuning up your bike, with parts available to use.
*[[Classroom]], general purpose room for projects and gatherings.
*[[CNC Room]], a small room with our CNC Routers and Machines.
*[[Electronics Lab]], circuit making/repair, 3D printing, CAD Design.
*[[Metal Shop]], weld and grind metal frames and pieces, or mill and turn precision parts.
*[[Pottery Studio]], a space for working with clay.
*[[Textiles Lab]], home of all things sewing and crafting.
*[[Wood Shop]], for sawing, sanding, gluing, and jointing wood.

*[[Maker Village]], dedicated rented workspaces.
*[[Expansion Space]], a large portion of our space used for project storage, eventually to be turned into more dedicated common spaces and rentable spaces.

Category:Pottery Studio

2025-07-16T01:22:07Z

AndrewT: Update with policy changes since studio opening.

[[File:Pottery Shop.jpg|thumb]]
[[File:Pottery Shop 2.jpg|thumb|Inside the Pottery Studio]]
[[File:Pottery Kiln.jpg|thumb|Kiln Area]]

==About==
The pottery studio at the Port City Makerspace is a dedicated space for potters and ceramic artists to create, experiment, and develop their skills.

==Studio-Provided Tools==
*Potter's needles
*Cut-off wires
*Fettling knives
*Ribs and scrapers
*Loop, wire and ribbon tools
*Wooden modeling tools
*Sponges
*Assorted forms and templates
*Brushes
**Slip brushes have wood handles with brightly colored tips.
**Glaze brushes have all-wood handles.
**Wax resist brushes are brightly colored, Crayola branded, and have no wood. '''Wash wax resist brushes separately from glaze and slip brushes.'''

==Available Consumables==
===Clay===
(See the [https://www.portcitymakerspace.com/shop-store/ Shop Store] for current offerings and to make purchases.)
====Laguna Clay====
*B-Mix 5
**Its smooth, porcelain texture is a pleasure to throw and form, and it fires to a cream color in oxidation.
**Shrinkage ~12.0%; Absorption ~2.3%
*B-3 Brown
**Pliable clay with smooth grog and color from manganese and iron. Fires brown/black in oxidation.
**Shrinkage ~10.0%; Absorption ~3.0%
*No.50
**Light sand color with fine black specks that show through glazes. Excellent throwing body.
**Shrinkage: ~12.0%; Absorption ~2.93%
*No.55
**Off-white stoneware clay excellent for wheel work. Minor speckling caused by fireclay.
**Shrinkage ~10.8%; Absorption ~1.9%
*No.60
**Tan/buff stoneware clay with specks that bleed through the glaze, giving the appearance of iron burning through, typical of reduction effects.
**Shrinkage ~10.9%; Absorption ~1.7%
*No.65
**A plastic stoneware body that works well for functional whiteware.
**Shrinkage ~13%; Absorption ~1%
*No.80
**Fires red-brown. Very plastic for throwing.
**Shrinkage ~14.0%; Absorption ~0.9%
====Standard Clay Company====
*266 Umbria
**Gives a reduction-like dark brown color in an electric kiln. Smooth and plastic. Good for all techniques.
**Shrinkage ~13%; Absorption ~1.4%

===Glazes===
*A Glaze Membership is required ''per person'' (inclusive of children) for access to PCMS glazes. For current monthly fees, see the [https://www.portcitymakerspace.com/shop-store/ Shop Store].
*Currently we are sourcing Amaco and Coyote glazes for brushing and layering. See studio manager with any questions about availability or requests for additions to our stock.
*Always check glaze labels for application instructions, firing tips and needs, and food-safety rating before using. '''If your glaze/glazes might run or be more fluid, label your piece requesting a cookie or stilt.'''

=="Pottery Jail"==
*If a piece of yours is missing from where you expected it to be, it may have found its way to "pottery jail" on the lowermost shelf of the glaze fire rack. A piece may be sent here if it has any issues, which may include:
**missing names, labels, logos, or marks;
**inadequate glazing (eg. glazed bottoms/feet, glaze too close to bottom on the sides, etc.);
**broken pieces; or
**any pieces needing further clarification or additional info on status before going into the kiln.
*If your piece is in pottery jail, speak with the Kiln Master or text to their phone number listed on the shelf to find out what's needed to get your piece back into the firing process.

==Pottery Studio User Guide==
====Safety Guidelines====
*Always wear appropriate attire: wear closed-toe shoes, and avoid loose clothing or jewelry that could get caught in equipment.
*Follow all safety instructions provided for the use of equipment (e.g., kilns, wheels and grinders).
*Do not operate any machinery without proper training.
*Report any accidents, injuries or equipment malfunctions immediately to the shop manager or general manager.

====Studio Usage & Equipment====
*Currently, members do not need to sign up for studio time in advance, but be aware this policy may need to change as demand increases.
*Respect others' studio time and workspace; avoid using another member's personal materials or equipment without permission.
*Clean all tools and workspaces after use (e.g., clean clay tools, wash wheels, brushes and buckets and wipe down workstations).
*Keep the studio tidy and organized, including cleaning up clay debris and assisting with emptying water buckets and maintaining clean sink and floors.

====Material Handling and Storage====
*Only use the glazes and clays purchased through the Port City Makerspace Pottery Studio. Any outside clay or glaze must be approved by the studio manager.
*Store personal materials in designated rented lockers and label them with your name.

====Kiln and Firing Policies====
*'''Only authorized personnel may operate the kiln. Do not attempt to fire your own pieces unless you have received proper training and approval from the shop manager.'''
*Pieces must be properly labeled or marked before the bisque firing, to ensure they are not mistakenly taken by others and to follow up on any firing incidents. Unmarked work will be held in "pottery jail" for a time till this is corrected.
*Firing schedules will usually be posted in advance. Always check with the kiln master regarding changes in schedules or specific firing needs (temperature, time, etc.).
*Any damage to the kiln or other equipment due to improper use may result in repair charges.

====Studio Expectations====
*Be respectful and considerate of other studio members.
*No disruptive or disrespectful behavior, including inappropriate language or actions.
*Be mindful of shared space and limit personal belongings to designated areas.

====Firing and Finished Work====
*Check the completions status of your work before coming to pick it up; a Slack message will usually be sent out when a kiln is unloaded. Be prepared to be flexible regarding delays or changes in firing schedules.
*Place your work on the proper shelf when it is ready for bisque and glaze firings.

====Membership and Studio Fees====
*Access to makerspace glazes requires a monthly glaze membership in addition to the general PCMS membership. '''Glaze memberships are per person, inclusive of children, not per family.'''

====Respect for Intellectual Property====
*Do not copy or replicate others' artwork without permission.
*Be mindful of others' privacy and work and do not photograph or share their creations without consent.

====Environmental and Community Responsibility====
*Recycle clay scraps and slip in the buckets by the wheels. '''Any clay that falls on the floor must be thrown out.''
*Please keep water usage to a minimum, and adhere to the rules and requirements of the sink and cleaning process.
*Give yourself enough time to make sure you're leaving the studio ''as you wish you'd find it.''

==Lockers==
*Pottery storage spaces are available for rent. For current monthly fees, see the [https://www.portcitymakerspace.com/shop-store/ Shop Store].
*17″x15″ storage spaces with a card tag, a ventilated door, and an independent locking system.
*Space holds up to 55 pounds.

[[Category: Spaces]]

Small Skutt Kiln

2025-07-15T23:52:50Z

AndrewT: AndrewT moved page Small Skutt Kiln to Pottery Kiln (Small)

#REDIRECT [[Pottery Kiln (Small)]]

Pottery Kiln (Small)

2025-07-15T23:52:50Z

AndrewT: AndrewT moved page Small Skutt Kiln to Pottery Kiln (Small)

[[File:Small Skutt Kiln.jpg|400px|thumb|"Baby" Kiln]]

=About our machine=
*Model: Skutt Automatic Kiln KM-818
*'''This tool is OFF LIMITS except to authorized staff and volunteers.'''
*'''Kiln operates on a weekly schedule.'''

=Guides and Manuals=
*[https://drive.google.com/file/d/13Rto2ZyWUwuK051LGYNFIgabutRKadxz/view?usp=drive_link Skutt Kilnmaster Kiln]

=Safety=
*'''Again, this tool is OFF LIMITS except to authorized staff and volunteers.'''
*''Per Kiln Master's instructions, do not unload kiln when it is above 100°F.''
*The stainless steel jacket and some of the other fixtures surrounding the kiln will get hot enough to burn your skin when the kiln is heated.
*Use fire rated gloves to protect your skin and make sure clothing is kept well away from any kiln opening or hot kiln surface.
*Never insert metal instruments or place any part of your body into the kiln while it is firing.
*Do not place combustibles in your kiln, such as: paper (except specific shelf liner fiber-paper used for glass applications), cardboard, wood, plastic, etc.
*Items that may be damp (i.e. greenware, kiln shelves) have the potential to crack or explode inside the kiln when the moisture trapped inside them turns to vapor when heated.
*Never allow your kiln to exceed the temperature rating listed on the serial plate.

=Maintenance=
*Vacuum floor and element grooves regularly. Carefully vacuum around thermocouple and elements. Leave KM kilns plugged in when you are vacuuming to ground any static charges that may occur at the nozzle tip of the vacuum. Try to keep the vacuum away from the touch pad area. Inspect Plug and Wall receptacle for any indication of excessive heat. Replace both plug and receptacle if necessary.
*Glaze drips on a properly kiln washed floor can easily be removed without damage to the surface below. Remember to remove all glaze drips before taking the kiln to porcelain/stoneware temperatures, where the glaze will over-fire and soak through the kiln wash.

[[Category: Tool]]
[[Category: Pottery Studio]]
[[Category: Safety Checkout]]

Skutt Kiln

2025-07-15T23:52:34Z

AndrewT: AndrewT moved page Skutt Kiln to Pottery Kiln (Big)

#REDIRECT [[Pottery Kiln (Big)]]

Pottery Kiln (Big)

2025-07-15T23:52:34Z

AndrewT: AndrewT moved page Skutt Kiln to Pottery Kiln (Big)

[[File:Skutt Kiln.jpg|400px|thumb|Skutt Kilnmaster KM-1027]]

=About our machine=
*Model: Skutt Kilnmaster Kiln KM-1027
*'''This tool is OFF LIMITS except to authorized staff and volunteers.'''
*''Per Kiln Master's instructions, do not unload while kiln is above 100°F.''

=Guides and Manuals=
*[https://drive.google.com/file/d/13Rto2ZyWUwuK051LGYNFIgabutRKadxz/view?usp=drive_link Skutt Kilnmaster Kiln]

=Safety=
*'''Again, this tool is OFF LIMITS except to authorized staff and volunteers.'''
*The stainless steel jacket and some of the other fixtures surrounding the kiln will get hot enough to burn your skin when the kiln is heated.
*Use fire rated gloves to protect your skin and make sure clothing is kept well away from any kiln opening or hot kiln surface.
*Never insert metal instruments or place any part of your body into the kiln while it is firing.
*Do not place combustibles in your kiln, such as: paper (except specific shelf liner fiber-paper used for glass applications), cardboard, wood, plastic, etc.
*Items that may be damp (i.e. greenware, kiln shelves) have the potential to crack or explode inside the kiln when the moisture trapped inside them turns to vapor when heated.
*Never allow your kiln to exceed the temperature rating listed on the serial plate.

=Maintenance=
*Vacuum floor and element grooves regularly. Carefully vacuum around thermocouple and elements. Leave KM kilns plugged in when you are vacuuming to ground any static charges that may occur at the nozzle tip of the vacuum. Try to keep the vacuum away from the touch pad area. Inspect Plug and Wall receptacle for any indication of excessive heat. Replace both plug and receptacle if necessary.

*Glaze drips on a properly kiln washed floor can easily be removed without damage to the surface below. Remember to remove all glaze drips before taking the kiln to porcelain/stoneware temperatures, where the glaze will over-fire and soak through the kiln wash.

[[Category: Tool]]
[[Category: Pottery Studio]]
[[Category: Safety Checkout]]

Kiln

2025-07-15T23:51:50Z

AndrewT: AndrewT moved page Kiln to Tabletop Kiln: Distinguish it from the pottery studio kilns

#REDIRECT [[Tabletop Kiln]]

Tabletop Kiln

2025-07-15T23:51:50Z

AndrewT: AndrewT moved page Kiln to Tabletop Kiln: Distinguish it from the pottery studio kilns

[[File:tabletopkiln.jpg|400px|thumb|RapidFire Pro LP]]

=About our machines=
*Model: RAPIDFIRE PROGRAMMABLE PRO-LP from Tabletop Furnace
**from: Elizabeth Dalton
**Size (inside): 6″ x 5″ x 6″
**Power: 1500W
**Max temperature: 2200 F
**RapidFire kilns are designed to rapidly heat to 2200 F (1205 C) for jewelry, metal clays (PMC), glass fusing, glaze testing and ceramics.
*'''These tools require a safety checkout'''

=Guides and Manuals=
*[https://drive.google.com/file/d/1OXdXD-dtATw0iIz3c4uoJKgCtbgHcF25/view?usp=sharing RapidFire Pro LP Manual]

=General Tips and Safety=
*'''Ask before attempting to operate!'''
*Max temp: 2300F (do not operate at this temperature or higher. it is an old kiln and high heat will wear it out faster)

=Setup Checklist=
* Safe Location - is the kiln at least 30 feet from any combustible items? Is it in a safe location where it will be undisturbed?
* Inspect the kiln controls - do the switches turn on and off normally?
* Inspect the heater coils and bricks - is everything intact?
* When turning on - check the heat of the plug and cable. Is it too hot to touch?

=Helpful Videos=
*RapidFire Pro LP
**[https://www.youtube.com/watch?v=gHxoEomqEIo How to Program the TableTop Furnace RapidFire Pro]

=Maintenance=
*[https://www.youtube.com/watch?v=fpUedqtHr8I Repairing a Cracked Top or Bottom of an L&L Electric Kiln]
*[https://www.youtube.com/watch?v=BohGz_2KoKM Skutt Kiln Maintainence - Replacing the Kiln's Element]

Parts:
*[https://www.theceramicshop.com/store/category/39/232/peep-plugs/ Peep hole plugs]
*[https://hotkilns.com/parts?parts_category=All&kiln_series_nid=All&obsolete_series_nid=1049&PN=&title= L&L Kiln Parts]

=Supplies=
*[http://www.portlandpottery.com/ Portland Pottery Supply]
*[http://www.portlandpottery.com/cones/ Cones]
*[http://www.portlandpottery.com/laguna-low-fire-clay/ Low-fire clay]
*[http://www.portlandpottery.com/laguna-mid-range-clay-bodies/ Mid-fire clay]
*[http://www.portlandpottery.com/raku-clays-paper-clays-non-firing-clays/ Low or no-fire clay]
*[http://www.portlandpottery.com/teachers-pallete/ Glazes - Teacher's Pallete], easily inter-mixable colors

[[Category: Tool]]
[[Category: Safety Checkout]]

Pottery Kiln (Big)

2025-07-15T23:49:23Z

AndrewT:

Pottery Kiln (Big)

2025-07-15T23:48:13Z

AndrewT:

[[File:Skutt Kiln.jpg|400px|thumb|Skutt Kilnmaster KM-1027]]

=About our machine=
*Model: Skutt Kilnmaster Kiln KM-1027
*'''This tool is OFF LIMITS except to authorized staff and volunteers.'''
*'''Kiln operates on a weekly schedule at minimum.'''

=Guides and Manuals=
*[https://drive.google.com/file/d/13Rto2ZyWUwuK051LGYNFIgabutRKadxz/view?usp=drive_link Skutt Kilnmaster Kiln]

=Safety=
*'''Again, this tool is OFF LIMITS except to authorized staff and volunteers.'''
*''Per Kiln Master's instructions, do not unload while kiln is above 100°F.''
*The stainless steel jacket and some of the other fixtures surrounding the kiln will get hot enough to burn your skin when the kiln is heated.
*Use fire rated gloves to protect your skin and make sure clothing is kept well away from any kiln opening or hot kiln surface.
*Never insert metal instruments or place any part of your body into the kiln while it is firing.
*Do not place combustibles in your kiln, such as: paper (except specific shelf liner fiber-paper used for glass applications), cardboard, wood, plastic, etc.
*Items that may be damp (i.e. greenware, kiln shelves) have the potential to crack or explode inside the kiln when the moisture trapped inside them turns to vapor when heated.
*Never allow your kiln to exceed the temperature rating listed on the serial plate.

=Maintenance=
*Vacuum floor and element grooves regularly. Carefully vacuum around thermocouple and elements. Leave KM kilns plugged in when you are vacuuming to ground any static charges that may occur at the nozzle tip of the vacuum. Try to keep the vacuum away from the touch pad area. Inspect Plug and Wall receptacle for any indication of excessive heat. Replace both plug and receptacle if necessary.

*Glaze drips on a properly kiln washed floor can easily be removed without damage to the surface below. Remember to remove all glaze drips before taking the kiln to porcelain/stoneware temperatures, where the glaze will over-fire and soak through the kiln wash.

[[Category: Tool]]
[[Category: Pottery Studio]]
[[Category: Safety Checkout]]

Pottery Kiln (Small)

2025-07-15T23:46:26Z

AndrewT: Clarified user access and corrected PCMS unloading policy

Pottery Kiln (Big)

2025-07-15T23:42:28Z

AndrewT: Clarified who has access

[[File:Skutt Kiln.jpg|400px|thumb|Skutt Kilnmaster KM-1027]]

=About our machine=
*Model: Skutt Kilnmaster Kiln KM-1027
*'''This tool is OFF LIMITS except to authorized staff and volunteers.'''
*'''Kiln operates on a weekly schedule at minimum.'''

=Guides and Manuals=
*[https://drive.google.com/file/d/13Rto2ZyWUwuK051LGYNFIgabutRKadxz/view?usp=drive_link Skutt Kilnmaster Kiln]

=Safety=
*'''Again, this tool is OFF LIMITS except to authorized staff and volunteers.'''
*The stainless steel jacket and some of the other fixtures surrounding the kiln will get hot enough to burn your skin when the kiln is heated.
*Use fire rated gloves to protect your skin and make sure clothing is kept well away from any kiln opening or hot kiln surface.
*Never insert metal instruments or place any part of your body into the kiln while it is firing.
*Do not place combustibles in your kiln, such as: paper (except specific shelf liner fiber-paper used for glass applications), cardboard, wood, plastic, etc.
*Items that may be damp (i.e. greenware, kiln shelves) have the potential to crack or explode inside the kiln when the moisture trapped inside them turns to vapor when heated.
*Never allow your kiln to exceed the temperature rating listed on the serial plate.
*For your safety, the protection of your kiln, and the protection of your ware inside the kiln, we recommend that you avoid unloading the kiln when it is above 125°F (52°C).

=Maintenance=
*Vacuum floor and element grooves regularly. Carefully vacuum around thermocouple and elements. Leave KM kilns plugged in when you are vacuuming to ground any static charges that may occur at the nozzle tip of the vacuum. Try to keep the vacuum away from the touch pad area. Inspect Plug and Wall receptacle for any indication of excessive heat. Replace both plug and receptacle if necessary.

*Glaze drips on a properly kiln washed floor can easily be removed without damage to the surface below. Remember to remove all glaze drips before taking the kiln to porcelain/stoneware temperatures, where the glaze will over-fire and soak through the kiln wash.

[[Category: Tool]]
[[Category: Pottery Studio]]
[[Category: Safety Checkout]]

Rikon Bandsaws

2025-07-15T23:36:23Z

AndrewT: AndrewT moved page Rikon Bandsaws to Rikon Bandsaws (ARCHIVED): Bandsaws have been sold

#REDIRECT [[Rikon Bandsaws (ARCHIVED)]]

Rikon Bandsaws (ARCHIVED)

2025-07-15T23:36:23Z

AndrewT: AndrewT moved page Rikon Bandsaws to Rikon Bandsaws (ARCHIVED): Bandsaws have been sold

[[File:rikonbandsawblue.jpg|400px|thumb|Rikon 10-326 with a large blade]]
[[File:rikonbandsawgreen.jpg|400px|thumb|Rikon 10-325 with a small blade]]

'''ARCHIVAL PAGE - We had two Rikon bandsaws.'''

The Blue one is a 10-326. It is equipped with a large blade, typically 5/8", and intended for making straight cuts.

The Green one is a 10-325. It is equipped with a small blade, typically 1/4", and is able to do straight or curved cuts.

Details on both Rikon bandsaws:
*Blade length: 111"
*Blade width: 3/16” - 3/4” (4.78 - 19 mm)
*Maximum Cutting Width (throat): 13-5/8” (346 mm)
*Maximum Cutting Depth (height): 13” (330 mm)

=Manual and Guides=
*[https://drive.google.com/file/d/124H4pD1FXnOCYNXIe1bREsKh59fAOAeL/view?usp=sharing Manual 10-326] (for Blue)
*[https://drive.google.com/open?id=1EQEM2lXQafXeuVqnCpdztxtcIfSTQIJF&authuser=admin@portcitymakerspace.com&usp=drive_fs Manual 10-325] (for Green)

=Use and Cleanup=
#Use the right blade for your job. A thicker blade (1/2" or larger) is best for straight cuts in thick material. A thinner blade (around 1/4" or smaller) is better for curved cuts in thin material.
#Adjust the blade guard to slightly above the material you will be cutting.
#Clean up when you are done. Use a handbroom or vacuum to clean the table, underneath the table, and the lower compartment where dust really collects.
#Lower the blade guard when you are done. This is for safety - less exposed blade means less risk to people in the shop.

=Videos=
Machine set up (Blue)
*[https://www.woodmagazine.com/video/bandsaw-basics Bandsaw Basics]
*[https://www.youtube.com/watch?time_continue=149&v=dRxiiC69Rk8 Bandsaw blades]
*[https://www.youtube.com/watch?v=noA-G1CSBc8 Rikon 10 326 Setup] - kennyearrings1
*[https://www.youtube.com/watch?v=FFZohxogGnQ Set up and tracking adjustment]
Machine set up (Green)
*[https://www.youtube.com/watch?v=w0f4x7XpMbY Rikon 14 inch 10-325 Band Saw, Installation and Setup]
*[https://www.youtube.com/watch?v=oct-UtIP9N0 Rikon 14" Bandsaw product tour]
Resawing
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
Cutting Logs
*[https://www.youtube.com/watch?v=YjeoS6va4PU Milling a Bowl blank on the Bandsaw: woodturning with Sam Angelo] - WYOMINGWOODTURNER
Cutting Bowls/Circles
*[https://www.youtube.com/watch?v=afGNbVrBiFE Band Saw Circle Cutting Jig] - Mike Waldt
*[https://www.youtube.com/watch?v=mBVIuHWPLrE Turning a Bowl on a Bandsaw] - EthAnswers by Stockroom Supply

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Rikon Bandsaws (ARCHIVED)

2025-07-15T23:33:45Z

AndrewT: Archival tag

Rikon Bandsaws (ARCHIVED)

2025-02-19T00:19:43Z

AndrewT:

[[File:rikonbandsawblue.jpg|400px|thumb|Rikon 10-326 with a large blade]]
[[File:rikonbandsawgreen.jpg|400px|thumb|Rikon 10-325 with a small blade]]

We had two Rikon bandsaws.

The Blue one is a 10-326. It is equipped with a large blade, typically 5/8", and intended for making straight cuts.

The Green one is a 10-325. It is equipped with a small blade, typically 1/4", and is able to do straight or curved cuts.

Details on both Rikon bandsaws:
*Blade length: 111"
*Blade width: 3/16” - 3/4” (4.78 - 19 mm)
*Maximum Cutting Width (throat): 13-5/8” (346 mm)
*Maximum Cutting Depth (height): 13” (330 mm)

=Manual and Guides=
*[https://drive.google.com/file/d/124H4pD1FXnOCYNXIe1bREsKh59fAOAeL/view?usp=sharing Manual 10-326] (for Blue)
*[https://drive.google.com/open?id=1EQEM2lXQafXeuVqnCpdztxtcIfSTQIJF&authuser=admin@portcitymakerspace.com&usp=drive_fs Manual 10-325] (for Green)

=Use and Cleanup=
#Use the right blade for your job. A thicker blade (1/2" or larger) is best for straight cuts in thick material. A thinner blade (around 1/4" or smaller) is better for curved cuts in thin material.
#Adjust the blade guard to slightly above the material you will be cutting.
#Clean up when you are done. Use a handbroom or vacuum to clean the table, underneath the table, and the lower compartment where dust really collects.
#Lower the blade guard when you are done. This is for safety - less exposed blade means less risk to people in the shop.

=Videos=
Machine set up (Blue)
*[https://www.woodmagazine.com/video/bandsaw-basics Bandsaw Basics]
*[https://www.youtube.com/watch?time_continue=149&v=dRxiiC69Rk8 Bandsaw blades]
*[https://www.youtube.com/watch?v=noA-G1CSBc8 Rikon 10 326 Setup] - kennyearrings1
*[https://www.youtube.com/watch?v=FFZohxogGnQ Set up and tracking adjustment]
Machine set up (Green)
*[https://www.youtube.com/watch?v=w0f4x7XpMbY Rikon 14 inch 10-325 Band Saw, Installation and Setup]
*[https://www.youtube.com/watch?v=oct-UtIP9N0 Rikon 14" Bandsaw product tour]
Resawing
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
Cutting Logs
*[https://www.youtube.com/watch?v=YjeoS6va4PU Milling a Bowl blank on the Bandsaw: woodturning with Sam Angelo] - WYOMINGWOODTURNER
Cutting Bowls/Circles
*[https://www.youtube.com/watch?v=afGNbVrBiFE Band Saw Circle Cutting Jig] - Mike Waldt
*[https://www.youtube.com/watch?v=mBVIuHWPLrE Turning a Bowl on a Bandsaw] - EthAnswers by Stockroom Supply

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Resaw Bandsaw

2025-02-18T22:20:10Z

AndrewT:

[[File:Rockwell Resaw Bandsaw.jpg|400px|thumb]]

==About our machine==
*Model#: Rockwell Model 20 (clone to Delta 28-340)
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link Manual]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax
*Periodically: Clean sap, resin, and dust off wheels. Lubricate sliding parts with light oil.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

File:Rockwell Resaw Bandsaw.jpg

2025-02-18T22:19:44Z

AndrewT:

Resaw Bandsaw

2025-02-18T22:18:42Z

AndrewT:

[[File:Rockwell_Resaw_Bandsaw.jpg|400px|thumb]]

==About our machine==
*Model#: Rockwell Model 20 (clone to Delta 28-340)
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link Manual]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax
*Periodically: Clean sap, resin, and dust off wheels. Lubricate sliding parts with light oil.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Resaw Bandsaw

2025-02-18T22:18:31Z

AndrewT:

[[File:RockwellResawBandsaw.jpg|400px|thumb]]

==About our machine==
*Model#: Rockwell Model 20 (clone to Delta 28-340)
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link Manual]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax
*Periodically: Clean sap, resin, and dust off wheels. Lubricate sliding parts with light oil.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Resaw Bandsaw

2025-02-18T22:18:04Z

AndrewT:

Resaw Bandsaw

2025-02-18T22:15:37Z

AndrewT:

[[File:ResawBandsawOden.jpg|400px|thumb]]

==About our machine==
*Model#: Rockwell Model 20 (clone to Delta 28-340)
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link Manual]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax
*Periodically: Clean sap, resin, and dust off wheels. Lubricate sliding parts with light oil.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Resaw Bandsaw

2025-02-18T22:10:48Z

AndrewT: /* Maintenance */

[[File:ResawBandsawOden.jpg|400px|thumb]]

==About our machine==
*Model#: Delta 28-340
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link Manual]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax
*Periodically: Clean sap, resin, and dust off wheels. Lubricate sliding parts with light oil.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Resaw Bandsaw

2025-02-18T22:09:35Z

AndrewT: /* Important Notes */

[[File:ResawBandsawOden.jpg|400px|thumb]]

==About our machine==
*Model#: Delta 28-340
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link Manual]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Resaw Bandsaw

2025-02-18T22:09:10Z

AndrewT:

[[File:ResawBandsawOden.jpg|400px|thumb]]

==About our machine==
*Model#: Delta 28-340
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link Manual]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE. Ask Oden if you think any adjustment is needed. It more than likely does not.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Resaw Bandsaw

2025-02-18T22:07:30Z

AndrewT: Updating info for new bandsaw

[[File:ResawBandsawOden.jpg|400px|thumb]]

==About our machine==
*Model#: Delta 28-340
*Wheel diameter: 20"
*Blade: 150" by 0.5", 3 TPI
*Max cutting height: 11.875"
*Max cutting width (with guide): TBD
*This is the perfect machine for cutting veneer or slicing large lumber into thinner boards.
*REQUIRES SAFETY CHECKOUT TO RECEIVE ACCESS
*[https://drive.google.com/file/d/1B2Iie5mSCIU1jLEdsEOGkx_ufoClD0aj/view?usp=drive_link]

==Important Notes==
*'''Shut it off immediately if it stalls or gets stuck'''. The motor can burn out if it stalls.
*'''Do not force wood through.''' The saw can cut very fast, but it may slow down going through knots or dense parts of wood, and suddenly speed up or jump after it goes through.
*Secure round or odd-shaped material to a sled. Do not cut unstable items - if they roll or shift during the cut they can jam and damage the blade.
*Finish your cut by pulling from the backside of the machine.
*DO NOT finish your cut by pushing with your hand or a pushstick.
*DO NOT CUT RECLAIMED LUMBER WITH ANY METALS JUST LIKE THE REST OF OUR SAWS.
*DO NOT ADJUST THE TENSION, GUIDES, OR BLADE. Ask Oden if you think any adjustment is needed. It more than likely does not.

==Instructional Resawing Videos==
*[https://www.youtube.com/watch?v=zi1RI3Ea4FY Woodworking Tips: Band Saw - Resawing] - WoodWorkers Guild Of America
*[https://www.youtube.com/watch?v=fK9m5PadmiI The physics of bandsaw resawing] - Matthias Wandel
*[https://www.youtube.com/watch?v=bfmCV7qKtGk Bandsaw Lumber: Sawing Firewood into Useable Boards] - Nick Engler (REMEMBER, DO NOT CUT WOOD YOU AREN'T SURE IS METAL-FREE)

==Maintenance==
*Every use: Clean dust off the machine's surface and moving parts
*As needed: Steel surface should be coated with a thin layer of paste wax

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Belt and Disc Sander

2024-12-17T23:10:35Z

AndrewT: /* Maintenance */

[[File:beltanddiscsander.jpg|400px|thumb]]

=About our machine=
*ShopFox Belt and Disc Sander W1676
**6" x 48" belt, 10" disc, typically 80 grit
*Delta 12" Disc Sander 31-122
**12" Disc, typically 220 grit

=Guides and Manuals=
*[https://drive.google.com/open?id=1ciKA4EcyjryV_Ik2L_HK-KglcVp5s4Tg ShopFox Belt and Disc Sander]
*[https://drive.google.com/open?id=1JMKsiNXFkLUaIOqo9gFY67eUTk5SEaDT Delta 12" Disc Sander]

=General Tips and Safety=
*

=Helpful Videos=
*

=Maintenance=
'''Periodically'''
* Check switch, cords and plugs and replace if worn.
* Replace damaged sanding belts or discs.
* Tighten mounting bolts.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Belt and Disc Sander

2024-12-17T23:10:03Z

AndrewT: Updated Maintenance with info from the tool maintenance spreadsheet.

[[File:beltanddiscsander.jpg|400px|thumb]]

=About our machine=
*ShopFox Belt and Disc Sander W1676
**6" x 48" belt, 10" disc, typically 80 grit
*Delta 12" Disc Sander 31-122
**12" Disc, typically 220 grit

=Guides and Manuals=
*[https://drive.google.com/open?id=1ciKA4EcyjryV_Ik2L_HK-KglcVp5s4Tg ShopFox Belt and Disc Sander]
*[https://drive.google.com/open?id=1JMKsiNXFkLUaIOqo9gFY67eUTk5SEaDT Delta 12" Disc Sander]

=General Tips and Safety=
*

=Helpful Videos=
*

=Maintenance=
'''Periodically'''
Check switch, cords and plugs and replace if worn.
Replace damaged sanding belts or discs.
Tighten mounting bolts.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

NOVA Galaxi Wood Lathe

2024-12-17T22:54:43Z

AndrewT: Updating Maintenance section from tool maintenance spreadsheet.

'' '''PAGE IN PROGRESS''' ''

[[File:Galaxi_Placeholder.jpg|400px|thumb|Stock Image of NOVA Galaxi]]
=About our machine=
'''This tool requires a safety checkout'''

====Lathe====
*Manufacturer: NOVA
*Model: Galaxi DVR Woodturning Lathe
*Capacity: 16" Swing Over Bed, 44" Between Centers
*Speeds: 100 to 5,000 rpm continuous variable speed
*Spindle: 1-1/4″ x 8 TPI RH
*Spindle Taper: MT2 Hollow
*Hole Through Headstock: 15mm, almost 19/32"
*Hole Through Tailstock: 12.5mm, almost 1/2"

=Guides and Manuals=
*[https://drive.google.com/file/d/1FtJPB7efOxSiOrsRR_NLi20OWesXr5S9/view?usp=sharing Galaxi DVR 1644 manual]

=General Tips and Safety=
'''VVV___REQUIRED SAFETY VIDEOS___VVV:'''

Members must watch these videos before using the lathe.
*[https://youtu.be/7yhkeUP6Mf8 Woodworking Tips & Techniques - Lathe Safety] (3 min)
*[https://youtu.be/YybjAs5T_r8 10 Common Wood Turning Mistakes] (14 min)
*[https://youtu.be/YVD0DLCGLCo Woodturning - Beginners Guide Revisited #1 - The Spindle Roughing Gouge] (12 min)

'''Important Safety Rules:'''
*Remove any jewelry, roll up sleeves, and otherwise secure anything that could get wrapped up in the machine.
*Position the tool rest as close as possible to the material without colliding.
*After adjusting the tool rest, BEFORE TURNING IT ON spin the workpiece by hand to make sure it will not collide.
*'''Safety eye wear required.''' Faceshields are highly recommended. Safety glasses are okay, but less effective.
*Always use sharp tools! Dull tools cause chip-out, but more importantly can get caught on your material.
*Avoid using materials that may break apart. Split wood, laminated materials, rotted pieces, etc.

'''General Tips'''
*Wear an apron or smock. Turning gets pretty messy.
*

=Helpful Videos=
*[https://www.youtube.com/watch?v=kunZIzNNxUY Understanding a Starter Set of Lathe Chisels | Woodworkers Guild of America] - WoodWorkers Guild Of America on Youtube
*[https://www.youtube.com/watch?v=zWFmsHDQIKs Spindle Turning Safety for the Wood Lathe] - WYOMINGWOODTURNER on Youtube

=Maintenance=

'''Monthly'''
* Check tightness of nuts and bolts
* Lubricate, with one or two drops of light-weight oil, the tailstock quill threads, index pin shaft, and the Toolslide camshaft (remove plastic plugs) and Toolslide front camshaft bore
* Wax & buff exposed cast iron parts, especially the bed rails

'''Every Six Months'''
* Lubricate the tailstock slot with one or two drops of lightweight oil.

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

NOVA Galaxi Wood Lathe

2024-12-17T22:13:30Z

AndrewT: /* About our machine */

'' '''PAGE IN PROGRESS''' ''

[[File:Galaxi_Placeholder.jpg|400px|thumb|Stock Image of NOVA Galaxi]]
=About our machine=
'''This tool requires a safety checkout'''

====Lathe====
*Manufacturer: NOVA
*Model: Galaxi DVR Woodturning Lathe
*Capacity: 16" Swing Over Bed, 44" Between Centers
*Speeds: 100 to 5,000 rpm continuous variable speed
*Spindle: 1-1/4″ x 8 TPI RH
*Spindle Taper: MT2 Hollow
*Hole Through Headstock: 15mm, almost 19/32"
*Hole Through Tailstock: 12.5mm, almost 1/2"

=Guides and Manuals=
*[https://drive.google.com/file/d/1FtJPB7efOxSiOrsRR_NLi20OWesXr5S9/view?usp=sharing Galaxi DVR 1644 manual]

=General Tips and Safety=
'''VVV___REQUIRED SAFETY VIDEOS___VVV:'''

Members must watch these videos before using the lathe.
*[https://youtu.be/7yhkeUP6Mf8 Woodworking Tips & Techniques - Lathe Safety] (3 min)
*[https://youtu.be/YybjAs5T_r8 10 Common Wood Turning Mistakes] (14 min)
*[https://youtu.be/YVD0DLCGLCo Woodturning - Beginners Guide Revisited #1 - The Spindle Roughing Gouge] (12 min)

'''Important Safety Rules:'''
*Remove any jewelry, roll up sleeves, and otherwise secure anything that could get wrapped up in the machine.
*Position the tool rest as close as possible to the material without colliding.
*After adjusting the tool rest, BEFORE TURNING IT ON spin the workpiece by hand to make sure it will not collide.
*'''Safety eye wear required.''' Faceshields are highly recommended. Safety glasses are okay, but less effective.
*Always use sharp tools! Dull tools cause chip-out, but more importantly can get caught on your material.
*Avoid using materials that may break apart. Split wood, laminated materials, rotted pieces, etc.

'''General Tips'''
*Wear an apron or smock. Turning gets pretty messy.
*

=Helpful Videos=
*[https://www.youtube.com/watch?v=kunZIzNNxUY Understanding a Starter Set of Lathe Chisels | Woodworkers Guild of America] - WoodWorkers Guild Of America on Youtube
*[https://www.youtube.com/watch?v=zWFmsHDQIKs Spindle Turning Safety for the Wood Lathe] - WYOMINGWOODTURNER on Youtube

=Maintenance=
*

Parts:
*

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Category:CNC Routers

2024-11-12T22:18:32Z

AndrewT: Swapped photo of old layouts with new space.

[[File:CNC "Room".jpg|400px|thumb|Shapeoko 5 visible up front, with Shapeoko 3 against back wall]]

==About our machines==
*This page is for info relating to our various CNC Routers.
*Models:
**[[Fireball V90 CNC]]
**[[Shapeoko 3]] (33"x17")
**[[Shapeoko 5]] (48"x48")
*Software:
**VCarve Pro
**CamBam

==Guides and Manuals==
Machines:
*[https://www.probotix.com/wiki/index.php/V90 Fireball V90] - Info on Probotix website
*[http://shapeoko.com/wiki/ Shapeoko CNC Wiki]

Software:
*[https://www.vectric.com/products/vcarve.htm VCarve Pro]
**[http://support.vectric.com/vcp-questions FAQs]
**[http://forum.vectric.com/ Forums]
**[http://support.vectric.com/tutorials/V9/?software=3&category=1&order=1 Tutorials]
**[http://gadgets.vectric.com/V9/library.html Gadgets]
**[http://support.vectric.com/tips-and-tricks/select.php Tips and Tricks]
*[Carbide Motion]
**[https://docs.carbide3d.com/assembly/carbidemotion/userguide/ User Manual]

==Safety==
*Never leave a CNC machine running unattended! If it crashes and you're not around to stop it, a lot of damage could be done to the machine and your workpiece.
*Wear safety glasses and hearing protection.

==Helpful Videos==
*[https://www.youtube.com/watch?v=Qm0kBXESY3o VCarve Pro Introduction]
*[https://www.youtube.com/watch?v=YBGqknN3gGs CNC Dummies for Routers - This Old Tony]
*[https://www.youtube.com/watch?v=J4bMAIEFCYU CNC Basics 2 - This Old Tony]

==Tooling Available==
There are a few bits we keep in stock:
*1/4 Endmill
*1/8 Endmills
*60 Degree V-bit (1/2" shank)
*90 Degree V-bit (1/2" shank)

We also have many bits with 1/8" shank size. Most of these are only appropriate in the [[Fireball V90 CNC]], but can be used in the others with a 1/4" to 1/8" adapter. If you use these adapters, be very cautious as they can't stand up to deep cuts and can slip out of the router.

==Other Resources==
*Feeds and Speeds
** https://community.carbide3d.com/t/shapeoko-feeds-and-speeds-chart-reformatted/5467
** https://shapeokoenthusiasts.gitbook.io/shapeoko-cnc-a-to-z/feeds-and-speeds-basics
** https://www.cnccookbook.com/feeds-speeds/
** https://makezine.com/article/digital-fabrication/machining/cnc-routing-basics-toolpaths-and-feeds-n-speeds/
**[http://precisebits.com/tutorials/calibrating_feeds_n_speeds.htm Calibrating Feeds and Speeds]
*[http://makezine.com/2014/12/04/50-digital-wood-joints-poster/ 50 Digital Wood Joints]
*[http://cncutil.org/gcode-introduction.html GCode Introduction]
*[http://www.autotracer.org/ Autotracer] - web-based tool to vectorize regular images
*[https://cloudconvert.com/ Convert anything to anything]
*[http://www.woodworkerb.com/home/pcb-isolation-routing/tool-width-calculator/ Calculator for finding width or depth of cut for a V-bit]
*[https://www.inventables.com/categories/materials Invetables - Materials]

[[Category: Tool]]
[[Category: Electronics Lab]]
[[Category: Safety Checkout]]

Category:CNC Room

2024-11-12T22:16:25Z

AndrewT: Swapped photo of old room with new space.

[[File:CNC "Room".jpg|400px|thumb]]

==Summary==
This is a small room dedicated to our CNC Router machines.

==Tools==
*[[Shapeoko 3]]
*[[Shapeoko 5]]
*[[Fireball V90 CNC]]

==Resources==

==Layout==

[[Category: Spaces]]

File:CNC "Room".jpg

2024-11-12T22:15:37Z

AndrewT:

MainMenu

2024-10-17T16:40:37Z

AndrewT: Updated Volunteer Manual link to connect to current file.

<span style="font-size:20px">Main Menu</span>
{| class="wikitable" style="text-align: center;"
|-
|'''General'''
|'''Spaces'''
|'''Tools'''
|'''Volunteer'''
|'''Instructors'''
|'''Community'''
|'''Communication'''
|- style="vertical-align:top;"

|
[http://www.portcitymakerspace.com Main Website]

[http://www.portcitymakerspace.com/events Events Calendar]

- - - - - -

[[:Category:Spaces]]

[[:Category:Tool]]

[[:Category:Member Resources]]

[[:Category:Projects]]

[[:Category:Volunteer]]

|

[[Auto Shop]]

[[Bike Shop]]

[[Class Room]]

[[CNC Room]]

[[Electronics Lab]]

[[Metal Shop]]

[[Textiles Lab]]

[[Wood Shop]]

|

[[:Category:Tool]]

[https://drive.google.com/open?id=0BzVFua5o5J7YfkFXS2V6RnI2N0xocW1HOGpRMmhtWHZ3OHh6TElkQVdxNGQtOW5yRDNqem8 Tool Manuals]

[https://drive.google.com/open?id=1SZ1rm5JCMRIMi-ZAhYHVTbz-E2XO922s MSDS Sheets]

|

[[:Category:Volunteer]]

[[Committees]]

[https://trello.com/b/MqJnX56X/desk-volunteers Desk Volunteer Trello]

[https://docs.google.com/forms/d/e/1FAIpQLSdhTCz7EjAB6Z2J9YTLE2VOu6anZ7x7yLvrOMuqy6bZDs45jg/viewform Volunteer Log]

[https://docs.google.com/document/d/15mpvdlusLNodWIVeW3LOz0Q22AAwcm7-1PTc3QTH8V8/edit?usp=sharing Volunteer Manual]

|
[[:Category:Instructor]]

[[Instructor Handbook]]

[https://docs.google.com/document/d/1TWlG6CD_VY5tr_5aqwGQQht6kyJLTa8cRtoKj0NhpgI/edit?usp=sharing Reimbursement Form] - paper

[https://docs.google.com/forms/d/e/1FAIpQLSf14WEmj-PGCxuc3I95aa3u9k3yA8Rb0rQfXM_HKdqLrOUceg/viewform Reimbursement Form] - digital

|
[[Member Resources]]

[[Slack]] - member chat

[https://www.facebook.com/groups/makerspacers/ PCMS Facebook Group]

[[Helpful Links]]

|

[[Board of Directors]]

[[Committees]]

[[List of Forms]]

- - - - - -

[https://www.portcitymakerspace.com/the-shop/codeofconduct/ Code of Conduct]

[https://docs.google.com/a/portcitymakerspace.com/forms/d/e/1FAIpQLSedW6qzzjHyghzZ6xrYgmNJOWycDUgToh9c8o_qjXzlV8Sxxg/viewform Maintenance Request Form]

[https://docs.google.com/forms/d/e/1FAIpQLSdozvwZiWFSMsdtE1kPHRu3bHUr9RMuhuvCJ_Qg2ZpVAYD_vw/viewform Facility Issue Reporting Form]

[https://docs.google.com/forms/d/e/1FAIpQLSe8HlKJMy_X5C9WjQNGnqCMwnjBkeqSVScGE-7ls6aHJLVYDw/viewform Entrance Survey]

[https://docs.google.com/forms/d/e/1FAIpQLSfGDYmNRKrSsFCmCBUq6DsQiP0Y_fXZlOG0SCWBmgCOamoQvg/viewform?usp=sf_link Feedback and Suggestions]

[https://docs.google.com/forms/d/1UGDuBa48ce35kriygEdNQE9DHW755gBbfxbfQVfQ16Q/edit Issue Reporting Form]

[https://docs.google.com/forms/d/e/1FAIpQLSd5L_f12g-McErkW4fvycb4IZ0PiYofy8RHEC1GQMAzRn510g/viewform Safety Checkout Form]

[https://docs.google.com/forms/d/e/1FAIpQLSenKWbfMIrtg2ggIadyZYjQ2Uekd6pqR4fJsV_xiZ65f75bLQ/viewform Purchase Request Form]

|}

NOVA Galaxi Wood Lathe

2024-10-08T23:57:14Z

AndrewT: Switched Rikon image for stock photo of new lathe

'' '''PAGE IN PROGRESS''' ''

[[File:Galaxi_Placeholder.jpg|400px|thumb|Stock Image of NOVA Galaxi]]
=About our machine=
'''This tool requires a safety checkout'''

====Lathe====
*Manufacturer: NOVA
*Model: Galaxi DVR Woodturning Lathe
*Capacity: 16" Swing Over Bed, 44" Between Centers
*Speeds: 100 to 5,000 rpm continuous variable speed
*Spindle: 1-1/4″ x 8 TPI RH
*Spindle Taper: MT2 Hollow
*Hole Through Headstock: 15mm, almost 19/32"
*Hole Through Tailstock: 12.5mm, almost 1/2"

====Chuck====
*'''TO BE FINISHED'''

=Guides and Manuals=
*[https://drive.google.com/file/d/1FtJPB7efOxSiOrsRR_NLi20OWesXr5S9/view?usp=sharing Galaxi DVR 1644 manual]

=General Tips and Safety=
'''VVV___REQUIRED SAFETY VIDEOS___VVV:'''

Members must watch these videos before using the lathe.
*[https://youtu.be/7yhkeUP6Mf8 Woodworking Tips & Techniques - Lathe Safety] (3 min)
*[https://youtu.be/YybjAs5T_r8 10 Common Wood Turning Mistakes] (14 min)
*[https://youtu.be/YVD0DLCGLCo Woodturning - Beginners Guide Revisited #1 - The Spindle Roughing Gouge] (12 min)

'''Important Safety Rules:'''
*Remove any jewelry, roll up sleeves, and otherwise secure anything that could get wrapped up in the machine.
*Position the tool rest as close as possible to the material without colliding.
*After adjusting the tool rest, BEFORE TURNING IT ON spin the workpiece by hand to make sure it will not collide.
*'''Safety eye wear required.''' Faceshields are highly recommended. Safety glasses are okay, but less effective.
*Always use sharp tools! Dull tools cause chip-out, but more importantly can get caught on your material.
*Avoid using materials that may break apart. Split wood, laminated materials, rotted pieces, etc.

'''General Tips'''
*Wear an apron or smock. Turning gets pretty messy.
*

=Helpful Videos=
*[https://www.youtube.com/watch?v=kunZIzNNxUY Understanding a Starter Set of Lathe Chisels | Woodworkers Guild of America] - WoodWorkers Guild Of America on Youtube
*[https://www.youtube.com/watch?v=zWFmsHDQIKs Spindle Turning Safety for the Wood Lathe] - WYOMINGWOODTURNER on Youtube

=Maintenance=
*

Parts:
*

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

File:Galaxi Placeholder.jpg

2024-10-08T23:56:09Z

AndrewT:

NOVA Galaxi Wood Lathe

2024-10-08T23:37:28Z

AndrewT: /* Lathe */

'' '''PAGE IN PROGRESS''' ''

[[File:Rikonwoodlathe.jpg|400px|thumb|NOT the NOVA Galaxi, yet]]
=About our machine=
'''This tool requires a safety checkout'''

====Lathe====
*Manufacturer: NOVA
*Model: Galaxi DVR Woodturning Lathe
*Capacity: 16" Swing Over Bed, 44" Between Centers
*Speeds: 100 to 5,000 rpm continuous variable speed
*Spindle: 1-1/4″ x 8 TPI RH
*Spindle Taper: MT2 Hollow
*Hole Through Headstock: 15mm, almost 19/32"
*Hole Through Tailstock: 12.5mm, almost 1/2"

====Chuck====
*'''TO BE FINISHED'''

=Guides and Manuals=
*[https://drive.google.com/file/d/1FtJPB7efOxSiOrsRR_NLi20OWesXr5S9/view?usp=sharing Galaxi DVR 1644 manual]

=General Tips and Safety=
'''VVV___REQUIRED SAFETY VIDEOS___VVV:'''

Members must watch these videos before using the lathe.
*[https://youtu.be/7yhkeUP6Mf8 Woodworking Tips & Techniques - Lathe Safety] (3 min)
*[https://youtu.be/YybjAs5T_r8 10 Common Wood Turning Mistakes] (14 min)
*[https://youtu.be/YVD0DLCGLCo Woodturning - Beginners Guide Revisited #1 - The Spindle Roughing Gouge] (12 min)

'''Important Safety Rules:'''
*Remove any jewelry, roll up sleeves, and otherwise secure anything that could get wrapped up in the machine.
*Position the tool rest as close as possible to the material without colliding.
*After adjusting the tool rest, BEFORE TURNING IT ON spin the workpiece by hand to make sure it will not collide.
*'''Safety eye wear required.''' Faceshields are highly recommended. Safety glasses are okay, but less effective.
*Always use sharp tools! Dull tools cause chip-out, but more importantly can get caught on your material.
*Avoid using materials that may break apart. Split wood, laminated materials, rotted pieces, etc.

'''General Tips'''
*Wear an apron or smock. Turning gets pretty messy.
*

=Helpful Videos=
*[https://www.youtube.com/watch?v=kunZIzNNxUY Understanding a Starter Set of Lathe Chisels | Woodworkers Guild of America] - WoodWorkers Guild Of America on Youtube
*[https://www.youtube.com/watch?v=zWFmsHDQIKs Spindle Turning Safety for the Wood Lathe] - WYOMINGWOODTURNER on Youtube

=Maintenance=
*

Parts:
*

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Category:Tool

2024-10-08T23:21:10Z

AndrewT:

This category is for tools available at the Makerspace.

For all available tool manuals, please see the '''[https://drive.google.com/open?id=0BzVFua5o5J7YfkFXS2V6RnI2N0xocW1HOGpRMmhtWHZ3OHh6TElkQVdxNGQtOW5yRDNqem8 Tool Manuals]''' folder on the shared google drive.
.

.

NOVA Galaxi Wood Lathe

2024-10-08T23:20:03Z

AndrewT: Created page with "'' '''PAGE IN PROGRESS''' '' NOT the NOVA Galaxi, yet =About our machine= '''This tool requires a safety checkout''' ====Lathe==== *Manufacturer: NOVA *Model: Galaxi DVR Woodturning Lathe *Capacity: '''TO BE FINISHED''' *Speeds: 100 to 5,000 rpm continuous variable speed *Spindle: 1-1/4″ x 8 TPI RH *Spindle Taper: MT2 Hollow *Hole Through Headstock: 15mm, almost 19/32" *Hole Through Tailstock: 12.5mm, almost 1/2" ====Chuck===..."

'' '''PAGE IN PROGRESS''' ''

[[File:Rikonwoodlathe.jpg|400px|thumb|NOT the NOVA Galaxi, yet]]
=About our machine=
'''This tool requires a safety checkout'''

====Lathe====
*Manufacturer: NOVA
*Model: Galaxi DVR Woodturning Lathe
*Capacity: '''TO BE FINISHED'''
*Speeds: 100 to 5,000 rpm continuous variable speed
*Spindle: 1-1/4″ x 8 TPI RH
*Spindle Taper: MT2 Hollow
*Hole Through Headstock: 15mm, almost 19/32"
*Hole Through Tailstock: 12.5mm, almost 1/2"

====Chuck====
*'''TO BE FINISHED'''

=Guides and Manuals=
*[https://drive.google.com/file/d/1FtJPB7efOxSiOrsRR_NLi20OWesXr5S9/view?usp=sharing Galaxi DVR 1644 manual]

=General Tips and Safety=
'''VVV___REQUIRED SAFETY VIDEOS___VVV:'''

Members must watch these videos before using the lathe.
*[https://youtu.be/7yhkeUP6Mf8 Woodworking Tips & Techniques - Lathe Safety] (3 min)
*[https://youtu.be/YybjAs5T_r8 10 Common Wood Turning Mistakes] (14 min)
*[https://youtu.be/YVD0DLCGLCo Woodturning - Beginners Guide Revisited #1 - The Spindle Roughing Gouge] (12 min)

'''Important Safety Rules:'''
*Remove any jewelry, roll up sleeves, and otherwise secure anything that could get wrapped up in the machine.
*Position the tool rest as close as possible to the material without colliding.
*After adjusting the tool rest, BEFORE TURNING IT ON spin the workpiece by hand to make sure it will not collide.
*'''Safety eye wear required.''' Faceshields are highly recommended. Safety glasses are okay, but less effective.
*Always use sharp tools! Dull tools cause chip-out, but more importantly can get caught on your material.
*Avoid using materials that may break apart. Split wood, laminated materials, rotted pieces, etc.

'''General Tips'''
*Wear an apron or smock. Turning gets pretty messy.
*

=Helpful Videos=
*[https://www.youtube.com/watch?v=kunZIzNNxUY Understanding a Starter Set of Lathe Chisels | Woodworkers Guild of America] - WoodWorkers Guild Of America on Youtube
*[https://www.youtube.com/watch?v=zWFmsHDQIKs Spindle Turning Safety for the Wood Lathe] - WYOMINGWOODTURNER on Youtube

=Maintenance=
*

Parts:
*

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]

Rikon Wood Lathe

2024-10-08T23:18:41Z

AndrewT: /* About our machine */

[[File:Rikonwoodlathe.jpg|400px|thumb|Rikon Wood Lathe]]
=About our machine=
*'''This tool requires a safety checkout'''

====Main Lathe====
*Model: Rikon 70-220VSR
*Capacity: 12.5" x 43"
*Speeds: 250 to 3,850 rpm
*Spindle: 1"x8TPI
*Spindle Taper: MT2
*Hole through spindle: 3/8"

====Chuck====
*Threads: 1 1/2" x 8 (use with adapter)

=Guides and Manuals=
*[https://drive.google.com/file/d/1Zoo56dYeroBFjP0AlJLjZgOuPIZcyNpq/view?usp=sharing Rikon 70-220VSR Manual]

=General Tips and Safety=
'''VVV___REQUIRED SAFETY VIDEOS___VVV:'''

Members must watch these videos before using the lathe.
*[https://youtu.be/7yhkeUP6Mf8 Woodworking Tips & Techniques - Lathe Safety] (3 min)
*[https://youtu.be/YybjAs5T_r8 10 Common Wood Turning Mistakes] (14 min)
*[https://youtu.be/YVD0DLCGLCo Woodturning - Beginners Guide Revisited #1 - The Spindle Roughing Gouge] (12 min)

'''Important Safety Rules:'''
*Remove any jewelry, roll up sleeves, and otherwise secure anything that could get wrapped up in the machine.
*Position the tool rest as close as possible to the material without colliding.
*After adjusting the tool rest, BEFORE TURNING IT ON spin the workpiece by hand to make sure it will not collide.
*'''Safety eye wear required.''' Faceshields are highly recommended. Safety glasses are okay, but less effective.
*Always use sharp tools! Dull tools cause chip-out, but more importantly can get caught on your material.
*Avoid using materials that may break apart. Split wood, laminated materials, rotted pieces, etc.

'''General Tips'''
*Wear an apron or smock. Turning gets pretty messy.
*

=Helpful Videos=
*[https://www.youtube.com/watch?v=kunZIzNNxUY Understanding a Starter Set of Lathe Chisels | Woodworkers Guild of America] - WoodWorkers Guild Of America on Youtube
*[https://www.youtube.com/watch?v=zWFmsHDQIKs Spindle Turning Safety for the Wood Lathe] - WYOMINGWOODTURNER on Youtube

=Maintenance=
*

Parts:
*

[[Category: Tool]]
[[Category: Wood Shop]]
[[Category: Safety Checkout]]