Category:CNC Routers: Difference between revisions
Jump to navigation
Jump to search
removing details about the Fireball V90 |
|||
| (6 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
[[File: | [[File:CNC "Room".jpg|400px|thumb|Shapeoko 5 visible up front, with Shapeoko 3 against back wall]] | ||
==About our machines== | |||
=About our machines= | |||
*This page is for info relating to our various CNC Routers. | *This page is for info relating to our various CNC Routers. | ||
*Models: | *Models: | ||
**[[ | **[[Shapeoko 3]] (33"x17") | ||
**[[Shapeoko]] | **[[Shapeoko 5]] (48"x48") | ||
*Software: | *Software: | ||
**VCarve Pro | **VCarve Pro | ||
**CamBam | **CamBam | ||
=Guides and Manuals= | ==Guides and Manuals== | ||
Machines: | Machines: | ||
*[http://shapeoko.com/wiki/ Shapeoko CNC Wiki] | *[http://shapeoko.com/wiki/ Shapeoko CNC Wiki] | ||
| Line 27: | Line 24: | ||
**[https://docs.carbide3d.com/assembly/carbidemotion/userguide/ User Manual] | **[https://docs.carbide3d.com/assembly/carbidemotion/userguide/ User Manual] | ||
= | ==Safety== | ||
* | *Never leave a CNC machine running unattended! If it crashes and you're not around to stop it, a lot of damage could be done to the machine and your workpiece. | ||
*Wear safety glasses and hearing protection. | |||
=Helpful Videos= | ==Helpful Videos== | ||
*[https://www.youtube.com/watch?v=Qm0kBXESY3o VCarve Pro Introduction] | *[https://www.youtube.com/watch?v=Qm0kBXESY3o VCarve Pro Introduction] | ||
*[https://www.youtube.com/watch?v=YBGqknN3gGs CNC Dummies for Routers - This Old Tony] | *[https://www.youtube.com/watch?v=YBGqknN3gGs CNC Dummies for Routers - This Old Tony] | ||
*[https://www.youtube.com/watch?v=J4bMAIEFCYU CNC Basics 2 - This Old Tony] | *[https://www.youtube.com/watch?v=J4bMAIEFCYU CNC Basics 2 - This Old Tony] | ||
= | ==Tooling Available== | ||
There are a few bits we keep in stock: | |||
*1/4 Endmill | |||
*1/8 Endmills | |||
* | *60 Degree V-bit (1/2" shank) | ||
* | *90 Degree V-bit (1/2" shank) | ||
**V- | |||
=Other Resources= | ==Other Resources== | ||
*Feeds and Speeds | *Feeds and Speeds | ||
** https://community.carbide3d.com/t/shapeoko-feeds-and-speeds-chart-reformatted/5467 | ** https://community.carbide3d.com/t/shapeoko-feeds-and-speeds-chart-reformatted/5467 | ||
Latest revision as of 15:15, 5 July 2025
About our machines
- This page is for info relating to our various CNC Routers.
- Models:
- Shapeoko 3 (33"x17")
- Shapeoko 5 (48"x48")
- Software:
- VCarve Pro
- CamBam
Guides and Manuals
Machines:
Software:
- VCarve Pro
- [Carbide Motion]
Safety
- Never leave a CNC machine running unattended! If it crashes and you're not around to stop it, a lot of damage could be done to the machine and your workpiece.
- Wear safety glasses and hearing protection.
Helpful Videos
Tooling Available
There are a few bits we keep in stock:
- 1/4 Endmill
- 1/8 Endmills
- 60 Degree V-bit (1/2" shank)
- 90 Degree V-bit (1/2" shank)
Other Resources
- Feeds and Speeds
- https://community.carbide3d.com/t/shapeoko-feeds-and-speeds-chart-reformatted/5467
- https://shapeokoenthusiasts.gitbook.io/shapeoko-cnc-a-to-z/feeds-and-speeds-basics
- https://www.cnccookbook.com/feeds-speeds/
- https://makezine.com/article/digital-fabrication/machining/cnc-routing-basics-toolpaths-and-feeds-n-speeds/
- Calibrating Feeds and Speeds
- 50 Digital Wood Joints
- GCode Introduction
- Autotracer - web-based tool to vectorize regular images
- Convert anything to anything
- Calculator for finding width or depth of cut for a V-bit
- Invetables - Materials
Pages in category "CNC Routers"
The following 2 pages are in this category, out of 2 total.