Bambu H2C Printer

Bambu Lab H2C

About our machines

This page is a work in progress, you are welcome to add useful information here

Bambu H2C Printer

• Build Volume: Single Nozzle Printing: 325*320*320 mm³ (Left) Single Nozzle Printing: 305*320*325 mm³ (Right) Dual Nozzle Printing: 300*320*325 mm³ Total Volume for Two Nozzles: 330*320*325 mm³
• Chassis: Aluminum and Steel
• Max Nozzle Temperature: 350℃
• Nozzle: Hardened Steel
• Supported Nozzle Diameter: 0.2 mm, 0.4 mm, 0.6 mm, 0.8 mm
• Filament Cutter: Built-in
• Filament Diameter: 1.75 mm
• Extruder Motor: Bambu Lab High-precision Permanent Magnet Synchronous Motor
• Max Heatbed Temperature: 120℃
• Max Toolhead Speed: 1000 mm/s
• Max Acceleration: 20,000 mm/s²
• Max Flow Rate: 40 mm³/s
• Max Chamber Temperature: 65℃
• HEPA Filter Grade: H12
• Activated Carbon Filter: Granulated Coconut Shell
• Supported Filaments: PLA, PETG, TPU, PVA, BVOH, ABS, ASA, PC, PA, PET, PPS, Carbon/Glass Fiber Reinforced Materials
• Live View, Nozzle, BirdsEye, Toolhead Camera: Built-in
• Filament Runout & Tangle Sensor: Supported
• Power Loss Recovery: Supported
• Voltage: 100–120 VAC / 200–240 VAC, 50/60 Hz
• Max Power: 1800W (220V) / 1250W (110V)
• Typical Power: 200W
• Slicer: Bambu Studio (Supports third-party slicers)

• Software
  • Bambu Studio

General Rules

• Reserve Time! For the printers, reserve time after your print starts on the Reserve Time page.
• Always Watch the First Layer! If a print doesn't start well, it's not going to end well.
  • If a print has more delicate features or overhangs that you think has a chance to fail, watch it more closely and check in on it.
• Do not log in to your personal Bambu account! If you wish to download files through their portal, please do so in the web browser or on your own computer. Logging into the Bambu software on the shared computers will change the standard settings other members are accustomed to and create confusion.
• Double-check your filament choice before printing! Make sure that all these match: the filament loaded in the machine, the material type in the Prepare screen in the Bambu software, and the final print screen when it is confirming what printer and which AMS slot you wish to use.
• Notes on Build Plates:
  • Textured plate - good for PLA and most plastics. The rough surface helps plastic hold on. Do not use glue on these.
  • Smooth plate - good for ABS, Nylon, and more difficult high-temp materials. Usually needs a thin layer of gluestick to help parts adhere.
  • Cleaning the plates - use soap and water or isopropyl alcohol to clean reside that may prevent prints from sticking to the bed.

Guides and Manuals

• [1] - Official setup and first print walkthrough
• [2] - H2 Series - Fix common print errors, hotend issues, and calibration problems
• [3] - H2 Series - Maintenance and How To Guides

Videos

• [4] - from BambuLab
• [5] - from BambuLab

Troubleshooting

The printers have a comprehensive system that shows an error code for many situations. You can look these codes up on BambuLab's website at the link below, and you will find instructions on how to fix almost everything.

HMS Error Codes - look up errors displayed on the printer when they occur to find troubleshooting instructions

Common Issues:

• Filament jam
  • If the filament roll is getting stuck in the AMS:
    • Roll is almost empty: try adding a desiccant pod in the inner space of the spool to help weight it down. When the spool is almost empty it becomes very easy for it to tip inside the AMS because it is so light.
• Print not sticking
  • If using a textured plate
    • Clean the plate with soap and water. Dry thoroughly. Try print again.
  • If using a smooth plate
    • Add a thin layer of glue stick and let it dry. Try print again.

Maintenance

• [6] - Regular Cleaning and Maintenance Recommendations for the H2C
• Bambu Lab How-To playlist - various quick videos on repair and replacement