Search results

*Spindle diameters: 4", 3", 2", 1-1/2", 1", 3/4", 5/8", 1/2", 3/8", 1/4"

[[File:Delta 23-665.jpg|400px|thumb|Delta 23-665, 1/3 HP, 3450 RPM]] [[File:Central_Machinery_39797.jpg|400px|thumb|Central Machinery 39797, 1/2 HP, 3450 RPM]]

***Under 1/4": 24TPI at 160fpm ***1/4-3/4": 14TPI at 160fpm

...nternational_4-1-2"_Bandsaw_BS5205.jpg|400px|thumb|General International 4-1/2" Bandsaw in Metal Shop]] *General International 4-1/2" Bandsaw BS5205

* Single drive ratios - 7, 9, 12, 17:1 * Double drive ratios - 7.5, 9.5, 13:1 (16:1 bobbin lead)

**Light: 1 switch on support column by thermostat **Light: 1 switch by main breaker panel in Wood Shop 2 (glue-up area)

*Spindle: 1"x8TPI *Threads: 1 1/2" x 8 (use with adapter)

** 2 in Auto Bay, 2 in Classroom, 1 in Electronics Lab *Zone 1 Light: 1 of the 2 switches by Wood Shop 2

***087 299 TIP, contact scr .023 wire x 1.125 ***000 067 TIP, contact scr .030 wire x 1.125

*Model: Consew 226R-1 ....com/file/d/1zHgOapnOPVCKj9BmZpmGWTvHpchZTOR3/view?usp=sharing Consew 226R-1 Manual]

*Common tungsten electrode sizes: 3/32 and 1/8 ...com/watch?v=aIyu-63ruMU Welding Basics & How-To TIG Weld - Livestream Part 1 of 2 - Eastwood]

The Green one is a 10-325. It is equipped with a small blade, typically 1/4", and is able to do straight or curved cuts. ...rger) is best for straight cuts in thick material. A thinner blade (around 1/4" or smaller) is better for curved cuts in thin material.

*Spindle: Dewalt Trim Router (accepts 1/4" shank)

Model#: 31-125 Type 1 *Keep fingers at least 1 inch away from the belt or disc at all times.

*Table Size: 20-1/4" x 7"

*Viktor S - 1/5/2020 *John L - 1/14/2020

Bed width: 31 1/2""

*1/4 Router Bits *1/2 Router Bits

...com/watch?v=BjudkxKWQ4U How to Sharpen End Mills on a Surface Grinder Part 1] - Build Something Cool

*EMPTY DUST COLLECTOR WHEN 1/2 FULL. Full bags go outside by trash. *Take light passes on harder woods (1/4 turn)

*Collet sizes: 1/8" to 1"

*Spindle thread: 1 7/8" - 8 *Spindle bore: 1 1/8"

*Spindle: 65mm Air-cooled 1200W spindle (accepts variety of bits from 1/8" to 1/4") ## Select the collet that matches the shank diameter of your tool (typically 1/4").

* Spindle: Makita Trim Router RT0701C (1/4" collet) * Leadscrews: 1/2", 10 threads/in, single-start

Ratios: 1 part indigo dye : 2 parts Sodium Hydrosulfite : 4 parts Soda Ash Use 1 gallon of water for every 5 grams of dye.

# For prints over 1 hour, ensure that you watch the print long enough that it looks like it is # Set the resin outside to cure for at least 1 hour in direct sunlight

*Max stock height allowance: 34mm (1.34") *[https://www.youtube.com/watch?v=1UygQiNqSQA Lesson #1 : First Time User]

*Spindle: Dewalt Trim Router (accepts 1/4" shank) *[https://my.carbide3d.com/pdf/shapeoko4_xl_assembly_guide_v1-1.pdf Shapeoko XL Assembly Guide] - A helpful anatomy of the machine.

...tps://www.youtube.com/watch?v=raLYRGDsILA Powermatic PM2800B Safety Video #1] '''- required to watch before operating'''

{|border="1"

* PLA is 1.24 g/cc. * Ramp 1: 300 F (8 hour ramp, 1 hour hold)

...ics solder. Recommended: [https://www.sparkfun.com/products/10242 Solder - 1/4lb Spool]

*3 In 1 Twin Air Filter Pressure Regulator Gauge Kit 3/8" Water/Oil Trap Separator *[https://www.amazon.com/dp/B07CVK9NWY/ref=sspa_dk_detail_2?psc=1 Glass Bead 60-80 grit] (20-60 PSI)

...or units. It is up to members to empty these out when they notice they are 1/2 to 3/4 full.

"Gen7 Arduino IDE Support v2.1" ...ino-IDE-Support-2.1/release%20documents/Gen7%20Arduino%20IDE%20Support%202.1.zip?raw=true

...ics solder. Recommended: [https://www.sparkfun.com/products/10242 Solder - 1/4lb Spool]

* To access tilting gears, remove cable clamp - 1 allen screw

# Be on Fire Watch for 1 hour after the flame has been put out. Stray embers or unseen hot metal cou

**Sub-Panel 1: Located in the bay with the car lift. Normally locked out and only accessi

| Max Material Height|| 34mm (1.34") || Over 250mm (10") ##'''Release the red E-stop button''' by rotating it clockwise a 1/4 turn. This turns on the laser controller.

'''posted Apr 20, 2014, 1:23 PM by Dave Strohschein'''

|1 Front Street Rollinsford, NH 03869 **[http://support.vectric.com/tutorials/V9/?software=3&category=1&order=1 Tutorials]